㈠產品特點：

1、適應門厚40-55mm；

2、使用場所：住宅、賓館、寫字樓等房門；

3、不銹鋼鎖舌襯板，壓鑄鎖舌體；

4、執手面板采用澳洲3#鋅合金材料制作,結合特殊的多層電鍍工藝，色澤持久、手感細膩，耐腐蝕性能優良，鹽霧實驗時間遠遠超過國標要求的24小時,再經硬度4H以上的清漆封閉，烤漆溫度達150℃；表面光滑，大大提高了防腐，防劃傷能力,且不沾灰塵油污。

lock features:

1、thickness of the door：40-50mm

2、site of use：the gate of house，hotel，and office building etc.

3、the scalebosrd of stainless steel lock bolt，die-casting lock bolt

4、Keep the hand face plate 3# zinc in Australia alligation material manufacture, combining many special lamellas plating craft, the color and luster endure, the feeling of hand is delicate, bearing to decay the function good, the salt fog experiment time marks 24 hours of request far above the country far, again through the 4 Hs of hardness above varnish seal, roast to paint the temperature to amount to 150℃s;The surface is smooth, raising the antisepsis consumedly, defending the scoring, scuffing ability.And don't be stained with the greasy dirt of dust.

㈡產品保養：

1、安裝鎖具前要仔細閱讀說明書，特別注意的是，在沒有刷油漆前開孔，油漆干后才將鎖安裝上。千萬不要在油漆未干就裝門鎖。油漆的揮發性氣體會減少鎖的使用壽命。

2、鎖具在平日開關門的過程中，最好握著執手把鎖舌旋進鎖體，關好門后再松手，不要用力撞門，否則會減少使用壽命。鎖具使用一段時間后，會出現開啟不順暢的現象，不要往鎖心內滴機油，將滑石粉或鉛筆心的細屑滑入鎖心內即可。

3、另外，不要用濕布擦拭鎖體和執手，因為有些金屬材質的鎖具會因此生銹；合金材質的鎖具會將鍍層磨掉，失去美觀的效果。

 Lock Maintenance of products:

1、Read carefully the specification of the lock before use. Note that if punching hole before being painted, then do not install the lock until the paint is dry. Never install it before the paint gets dry. The volatile gas of the paint can reduce the useful life.

2、In everday use, it is best to hole the handle to insert the lock-tongue into the lock. Do not let off until the door is closed. Do not bang the dcor, otherwise it would reduce its useful life. When used for a time, the lock may not be opened smoothly. Do not dip mechanical oil into the lock. Instead, slip some French chalk or pencil fines into it.

3、In addition, do not use wet cloth to wipe the lock and handle, because some metallic lock might get rusted. The alloy lock may lose its plated surace, and its brightness.

㈢安裝步驟：

A.       確保斜舌斜面與關門方向一致，根據安裝紙規畫線開孔。

B.        將鎖體放入孔。

C.        預緊襯板螺釘。

D.       將方桿穿過門板插入鎖體。

E.        安裝內外面板，使把手轉動順暢,預緊螺釘，(插入鎖芯)使鑰匙及旋鈕轉動順暢。

F.        安裝扣板及扣盒，對齊鎖體，應使鎖舌與之配合順暢，擰緊所有螺釘。

Installation steps: 

A.       Make sure the incline of the tongue go with the closing direction.

Draw lines and make holes according to the intallation specification.

B.        Place the lock into the hole.

C.        Pre-fix the screws of the back veneer.

D.       Insert the square bar through the door and into the lock.

E.        Install the inner and outer plates, making handle run smoothly.pre-fix the screws,（insert the lock cylinder）making the key and knob run smoothly.

F.        install the gusset plate and gusset box, make them parallel to the lock and match the lock tongue. Fix all the screws.